MK908 professional automotive scanner can perform various useful special functions like Oil Reset, SAS Calibration, EPB Service, DPF Regen, Battery Replacement, Throttle, Suspension, EGR, ABS Bleed, Injector Coding, Power Balance, active tests, adaptations, matching, initialization, and etc. NOTE: The Service Functions do NOT work on all vehicles. MK908 Wireless Diagnostic Scan Tool comes with MaxiVCI Mini dongle that enables technicians and mechanics to access and diagnose vehicles from ultra long 755 feet(230m) away. MK908 can access all available vehicle modules like PCM, ECM, EPS, PDM, BCM, TPM, SCCM and etc and perform OE-Level diagnosis to read/clear fault codes, view live data, perform active tests, matchings, adaptations, and etc.NOTE: AutoVIN depends on the cars ability, not on the device. 80+ MODELS COVERAGE, SOFTWARES UPDATE MOST FREQUENT? MK908 comes with broader vehicle coverage as Autel updates MK908 more often than MS906TS, MS906, MP808TS, MP808 and etc. It can work on 80+ US, European and Asian vehicles, mostly up to 2018, 2019 and for some up to 2020/2021.
With 9 non-standard adapters included, MK908 can access more models and modules. MK908 OBD2 Diagnostic Tool has bi-directional control capability over various car systems and components and is able to perform active tests (functional tests) like ABS bleeding, Motor Pump Test to determine the integrity of the system or parts by reading ECU data, or by commanding the the actuators, such as switching a solenoid, relay, or switch, between two operating states. ¦ Autel MaxiCom MK908 Brief Introduction. To check compatibility, please send VIN to us.With the VCI dongle, data transmission between the vehicle and the Diagnostic Scan Tool MK908 could be either through the USB cable or the VCI. This diagnostic computer MK908 can access and perform wireless diagnosis on vehicle's all systems and subsystems like ABS, SRS, EPB, BMS, SAS, DPF systems.
The IMMO service enables you to disable the lost vehicle keys, add a new key, key relearn and remote relearn. It could be one replacement key fob or more, depending on your needs. MK908 does NOT support OBDI vehicles.
Otherwise, it does NOT have ECU Programming capability. Autel MaxiCom MK908 Scan tool has very limited IMMO Keys function (Add New Keys). It only support add a new key for a very limited Asian cars, which have very low anti-thief systems.This add new key function is only for low-grade IMMO system vehicles, not intended for US cars, or AUDI, Benz, BMW, VW and any other vehicles that has more advanced IMMO systems. If you need IMMO function, please consider Autel IMMO tool, such as IM508.
Autel MK908 diagnostic scan tool features the latest VIN-based Auto VIN Technology that allows professionals and home mechanics to identify vehicle brand, year, make, model and etc at one touch. The Auto Scan function performs a comprehensive scanning over all the diagnosable ECUs in the vehicle's systems to locate and retrieve DTCs. Autel ADAS Compatibility for Safer Driving. Advanced Driver Assistance Systems (ADAS) is an array of vehicle systems that aid the driver either through passive alerts or by active control of the vehicle to drive safer and with greater awareness and precision. Autel ADAS Calibration Tool provides comprehensive and precise ADAS calibration.It covers vehicle makes including Benz, BMW, Audi, VW, Porsche, Infiniti, Lexus, GM, Ford, Volvo, Toyota, Nissan, Honda, Hyundai, and Kia. Supports the calibration of multiple driver assistant systems, including Adaptive. Cruise Control (ACC), Night Vision System (NVS), Lane Departure Warning (LDW), Blind Spot Detection (BSD), Around View Monitoring (AVM), Rear Collision Warning (RCW) and Heads-up Displays (HUD). All Car Systems OE-Level Diagnosis & Services. As an addition to the complete OBD2 functions of a normal OBD2 scanner, this professional diagnostic computer can diagnosis all car systems.
Oil reset to close the oil service light and reset service mileage & service interval after you replacing engine oil. EPB reset to brake reset the new electronic parking brake for braking wheels safely again. SAS reset to clear memories of the previous steering angle sensor and store the replaced one. DPF service supports forced fuel injector regeneration and adjustment. BMS service to reset battery management system.ABS brake bleeding to get a firm brake pad after air exhaustion. MK908 can NOT perform TPMS functions. As a professional grade car scan tool, MK908 has full Bi-Directional Control over vehicle-specific subsystem and components like ABS, SRS, window, door and roof. During a Bi-Directional control test, the tester outputs commands to the ECU in order to drive the actuators. This test determines the integrity of the system or parts by reading the engine ECU data, or by monitoring the operation of the actuators, such as switching a solenoid, relay, or switch, between two operating states. This function allows you to establish a data link to the electronic control system of the test vehicle via the VCI device for vehicle diagnosis, service or programming. You can operate functional tests, retrieve vehicle diagnostic information such as trouble codes, event codes and live data, and perform ECU coding, for various vehicle control systems, such as engine, transmission, ABS and more. ECU Coding is different from ECU Programming. And ECU Coding is NOT universally compatible. ABS Auto Bleed, Forced DPF regeneration, Adjusting Injectors, Relearn parking brake pad after replacement, Turn off oil service light and reset service mileage & service interval after you replacing engine oil. Reset service intervals after engine oil is changed.
Perform various active/functional tests to check ABS and SRS (Airbag) systems like ABS Brake Bleeding, Pump Motor Test and checking Module Information and etc. Deactivating and activating the brake control system, assisting with brake fluid control, opening and closing brake pads, and resetting brakes after disc or pad replacement and etc.
Clear steering angle sensor fault memory and reset the current steering wheel position as the straight-ahead position in the steering angle sensor EEPROM. Performs DPF Regeneration to clear the blockage through continuous burning of the particulate matter captured in the DPF filter and turn off DPF light.MK908 comes with 9 Non-Standard OBD2 Adapters as above only. It's normal to have empty slots in the package as the inner packing foam is not custom made for MK908.
Autel MaxiCom MK908 Wireless Automotive Scan Tool has full OBD2 coverage, the best possible coverage of OE-Level diagnosis on over 80 American, European and Asian vehicles with 9 non-standard OBD adapters included. Chrysler-16, Nissan-14, BMW-20, Kia-20, Honda-3, GM/Daewoo-12, Benz-38, Hyundai-12+16, VW/Audi-2+2. MK908 comes with 9 Non-Standard OBD Adapters as above only.
AndroidTM 4.4.2, KitKat. (1.3GHz Quad-core ARM Cortex-A7 + 1.7GHz Dual-core ARM Cortex-A15).
2GB RAM & 64GB On-board Memory. 10.1-inch LED screen with 1920x1200 resolutions. Wi-Fi (802.11 a/b/g/n/ac); USB: 2.0; BT v. 2.1 + EDR; SD Card (Support up to 32GB); HDMI. 8.0 Megapixel, AF with Flashlight.Gravity Accelerometer, Ambient Light Sensor (ALS). Microphone; Dual Speakers; 3-Band 3.5 mm stereo/standard headset jack; Power and Battery; 15000 mAh 3.8 V lithium-polymer battery; Charging via 12 V AC/DC power supply with the temperature between 0°C and 45°C.
0 to 50°C (32 to 122°F). 20 to 60°C (-4 to 140°F). Strong plastic housing with protective rubber boot.
312mm (12.28") x 208mm (8.18") x 36mm (1.41). 1.48kg (3.26 lb). ISO 9142-2, ISO 14230-2, ISO 15765-4, K/L-Line, Flashing Code, SAE-J1850 VPW, SAE-J1850 PWM, CAN ISO 11898, High-speed, Middle speed, Low speed and Singlewide CAN, GM UART, UART Echo Byte Protocol, Honda Diag-H Protocol, TP 2.0, TP 1.6, SAE J1939, SAE J1708, Fault-Tolerant CAN. This item is in the category "Vehicle Parts & Accessories\Garage Equipment & Tools\Diagnostic Equipment & Tools\Code Readers & Scanners". The seller is "autel-tool" and is located in this country: GB.
This item can be shipped to United Kingdom.